What Is a Fusion Splicer and How Does It Work?

Illustration of an electric arc fusing two optical fibers between electrodes

A fusion splicer joins two optical fibers by melting their ends together with an electric arc. Done properly, the joint is almost as strong as the original fiber and loses very little light, which is why fusion splicing is the standard method for permanent joints in telecom, ISP and data center networks. This article explains how the process works, the kinds of machine available and what keeps a splicer performing.

How fusion splicing works, step by step

  1. Strip. The protective coating is removed to expose bare glass, typically 125 micrometres in diameter.
  2. Clean. The bare fiber is wiped with lint-free wipes and isopropyl alcohol. Dust at this stage ends up inside the splice.
  3. Cleave. A precision cleaver scores and breaks the fiber to leave a flat end face at right angles to its axis. This is the step that most affects the result.
  4. Load and align. Both fibers are clamped into the splicer. Cameras inspect the end faces, and motors bring the fibers into alignment.
  5. Fuse. A short pre-fuse arc burns off any residue, then the main arc melts the ends while the machine pushes them together.
  6. Estimate and test. The splicer estimates the loss from the image and applies a small pull to confirm the joint holds.
  7. Protect. A heat-shrink sleeve with a steel strength member is slid over the splice and shrunk in the built-in heater.

Types of fusion splicer

  • Core alignment: aligns the fibers by imaging their cores. Lowest loss, highest price. Used on backbone and long-haul links.
  • Cladding alignment: aligns by the fiber's outer surface. Compact and fast. Used widely in FTTH and access networks.
  • Ribbon (mass fusion): splices up to twelve fibers in a ribbon at once. Used on high-fiber-count cables.
  • Speciality splicers: built for large-diameter, polarisation-maintaining or other unusual fibers in manufacturing and research.

Fusion splicing compared with mechanical splicing

Fusion splice Mechanical splice
Loss Very low, often a few hundredths of a dB Higher, often a few tenths of a dB
Back reflection Negligible Noticeable, depends on index gel
Equipment cost High Low
Cost per splice Low Higher
Long-term reliability Excellent Adequate for temporary or low-count work

Mechanical splices still have a place for emergency restoration and very small jobs. For anything permanent or at volume, fusion splicing wins on performance and on cost per joint.

What affects splice quality

  • Cleave angle and end-face quality. The largest single factor.
  • Cleanliness. Dirty V-grooves lift the fiber out of position. Dirty fiber leaves bubbles.
  • Arc condition. Altitude, temperature, humidity and electrode wear all change the arc. Run an arc calibration when conditions change.
  • Fiber mismatch. Joining fibers with different mode-field diameters produces loss that no machine can remove.

Maintenance that keeps a splicer accurate

  • Clean the V-grooves, fiber clamps and camera lenses regularly.
  • Clean the electrodes, and replace them when the arc counter reaches the manufacturer's limit.
  • Run an arc calibration at the start of a job and after moving to a different environment.
  • Keep firmware current, since updates often add fiber profiles.
  • Rotate the cleaver blade when cleave quality drops.

Testing the finished splice

The splicer's loss estimate is calculated from an image, so it cannot see everything. For commissioning, measure the link with an OTDR, ideally from both ends, or with a light source and power meter.

Browse our fiber optic test equipment for the instruments used to verify splices.

Frequently asked questions

How long does a fusion splice take?

The fusion itself takes seconds. Including preparation and heating the protection sleeve, an experienced technician completes a single-fiber splice in a few minutes.

Is a fusion splice as strong as the original fiber?

Close to it. The bare splice is weaker than coated fiber, which is why every splice is covered with a protection sleeve and stored in a splice tray.

Can different fiber types be spliced together?

Physically yes, but mismatched fibers produce higher loss. Single-mode to multimode joints are generally avoided.

Why does my splicer report high estimated loss?

Check the cleave first, then clean the V-grooves and run an arc calibration. Worn electrodes are the next most likely cause.