How to Choose a Thermal Camera for Industrial Use

Illustration of a handheld thermal camera showing a hot spot

A thermal camera turns surface temperature into a picture, so a loose connection, a failing bearing or a wet section of insulation shows up before it becomes a breakdown. Models range from pocket units to high-resolution inspection cameras, and the specification sheet decides which faults you will actually be able to see. This guide explains those specifications for maintenance engineers, electrical contractors, building surveyors and the people who buy for them.

How a thermal camera works

Every object emits infrared radiation in proportion to its temperature. A thermal camera focuses that radiation onto a detector array, usually an uncooled microbolometer, and converts each pixel's reading into a temperature. The result is a thermogram in which colour or brightness represents heat.

Two consequences follow. The camera measures surface temperature only, and the reading depends on the surface's emissivity, meaning how efficiently it radiates. Shiny bare metal is a poor emitter and reads falsely low unless you correct for it.

The specifications that matter

Detector resolution

Resolution is the number of temperature-measuring pixels. More pixels let you see smaller targets from further away.

Resolution Typical use
Around 160 x 120 Close-range troubleshooting and routine checks
Around 320 x 240 Professional electrical, mechanical and building surveys
640 x 480 and above Small or distant targets, detailed reporting, R&D

Check the true detector resolution. Some cameras quote an enhanced image resolution that is produced by processing.

Thermal sensitivity (NETD)

NETD is the smallest temperature difference the camera can distinguish, given in millikelvin. Lower is better. High sensitivity matters most where the differences are subtle, as in building and moisture surveys.

Temperature range and accuracy

Make sure the range covers your hottest target with margin. Electrical and building work fits comfortably in most cameras' ranges, while furnace and process work needs a high-temperature range. Accuracy for industrial cameras is commonly specified as plus or minus 2 °C or 2 percent of reading.

Field of view and lenses

A wide lens covers a whole panel or wall from close range. A telephoto lens resolves small components at a distance, such as overhead line hardware. Cameras with interchangeable lenses cover both.

Focus

Fixed-focus cameras are quick to use at normal working distances. Manual or automatic focus gives sharper images and more accurate readings on small targets, because a blurred image averages a hot spot with its surroundings.

Spot size

For a reliable reading, the target has to fill several pixels. The distance-to-spot ratio or IFOV on the data sheet tells you how small a target you can measure from a given distance.

Image blending and reporting

Overlaying a visible-light image on the thermal image makes it far easier to identify which component is hot. Radiometric image files, which store a temperature for every pixel, let you re-analyse the image and build reports afterwards.

Matching the camera to the job

  • Electrical inspection: 320 x 240 or better, a visible-light overlay, and enough range for loaded connections. Inspect under load and observe safe approach distances.
  • Mechanical maintenance: bearings, couplings, motors and steam traps. Ruggedness and fast focus matter more than maximum resolution.
  • Building diagnostics: high sensitivity and a wide lens for insulation gaps, air leakage and moisture.
  • Process and high-temperature work: an extended temperature range and, often, a telephoto lens.

Getting accurate readings

  • Set emissivity for the surface, or apply high-emissivity tape or paint to shiny metal.
  • Avoid reflections of hot objects, including yourself, on glossy surfaces.
  • Focus carefully and get close enough for the target to fill the measurement spot.
  • Compare similar components under similar load. A difference between phases tells you more than an absolute number.

Browse our thermal imaging collection for professional cameras.

Frequently asked questions

What resolution do I need?

For professional inspection work, 320 x 240 is a sensible minimum. Go higher if your targets are small or far away.

Can a thermal camera see through walls?

No. It shows the wall's surface temperature. Hidden pipes, studs or moisture appear only because they change that surface temperature.

Why does bare metal read cold?

Bare metal has low emissivity and reflects its surroundings. Correct the emissivity setting or measure on a painted or taped area.

Do I need training to use one?

The camera is simple to operate, but interpreting images correctly takes knowledge. Formal thermography training is worth it if you report findings to clients or insurers.